FPS Abrasion Tester

AB-2012

1-1

FPS Abrasion Tester

AB-2012

The AB-2012 FPS abrasion tester is a abrasion testing machine for performing abrasion tests on polymer materials (tires, belts, etc.).

Click here for automatic measurement>Go to technical information>
Summary


The AB-2012 FPS abrasion tester is a device to perform abrasion tests on polymer materials used in tires, belts, abrasions with high accuracy.

In addition to conventional slip rate control technology, this device is equipped with a new function to reduce control frictional force (tangential force), and it is possible to operate A test environment closer to actual vehicle conditions.

As a result, it is now possible to evaluate the frictional energy required by multiple test results using conventional methods.

Features
  1. Friction force control test
    • Friction force control, which was impossible with conventional devices (lamborn abrasion testers, etc.), has been discussed.
    • Based on actual vehicle conditions can be measured with high accuracy.
  2. Realtime discussion
    • The Diameter of the Strangely Worn during the Test is Worn, and the Slip Rate and Speed are feedback adjusted in real time.
  3. temperature control
    • The road surface temperature is controlled from room temperature +10℃ to 80℃ without using a slip ring.
  4. Improved sample clamping method
    • The clamping method was changed to a ratchet type to improve efficiency and operability.
  5. Designing of Designing Technology
    • Obtaining is being controlled by using a talc feeder (Japanese Patent No. 4559617) that can control the flow rate with high accuracy.
  6. Improvement of wear materials
    • A safety walk (special wear material) was considered to improve test reproducibility.
  7. Compatible with long-time tests
    • Fully automated tests are possible with a maximum of 56 millimeters with a diameter of 50 mm and a maximum of 24 millimeters with a diameter of 70 mm (optional).
  8. Test wheel surface cleaning function
    • A brush for cleaning the wheel surface is mounted, and the surface condition during the test is kept constant.
  9. Data analysis using dedicated software
    • Data processing such as friction energy analysis and graphing is significant, and test results can be analyzed in detail.
Main test exam


It is used for material testing of tires, belts, rubber rolls, etc., and can be manufactured in compliance with ISO standards and JIS standards. It is optimally optimized for high-quality automotive tire materials.

Test conditions
  • Diameter:50mm (maximum 56 pieces) or 70mm (maximum 24 pieces, optional).
  • Load: 10 to 80 N (optional setting).
  • Temperature: Maximum 250°C for both test wheels and road wheels (using a non-contact thermometer).
  • Slip rate: ± 30%
  • Test speed: test piece 10 to 210 m/min, road wheel 10 to 150 m/min
Safety device


Equipped with an emergency stop switch, door interlock, and overload protection.

Dimension And Specs
  • External dimensions: 1130mm (W) x 576mm (D) x 1855mm (H)
  • Weight: Approximately 380 kg (including dust collector and air dryer).
  • Power: AC200V three phase 30A 50/60Hz
  • Usage environment: JIS K 6250-2006 compliant.

This device realizes high-precision and efficient wear tests, and plays an important role in friction and wear resistance in the automotive industry and materials research.

MODEL AB-2012
Name FPS Wear Testing Machine
Test Specimen Shape Outer diameter 50mm, Width 10mm / Outer diameter 70mm, Width 20mm (Optional)
Road Surface Wheel Outer diameter 250mm, Width 30mm (Abrasive material: Sandpaper applied)
Load 10–80N (Arbitrary constant load)
Air cylinder drive, Load cell feedback control
Test Shaft Torque ~3–3Nm (Setting range)
Set Slip Ratio ±30%
Rotation Speed (Test Speed) Test specimen: 10–210 m/min, Road surface wheel: 10–150m/min
Automatic Specimen Transport Function The test specimens mounted on the turret are automatically transported for continuous testing
Number of Specimens Mounted Max 56 pieces (Test specimen: 50mm, Width 10mm)
Max 24 pieces (Test specimen: 70mm, Width 20mm - Optional)
Surface Temperature Measurement Non-contact thermometer: 0–250℃
Road Surface Temperature Control Room temperature +10℃ to 80℃
Talcum Powder Feeding rate: 0.1–0.8rpm
Data Processing (via PC) Test condition setting & stopping, Data acquisition, Graph plotting, Weight data acquisition, etc.
Safety Devices Emergency stop switch, Door interlock, Overload protection
Utility Power supply: AC 200V, Three-phase, 30A, 50/60Hz
Factory air: 0.5MPa–0.8MPa, Approx. 200L/min
Operating Environment Complies with JIS K 6250
Dimensions & Weight Approx. 1130 (W) × 675 (D) × 1855 (H) mm, Approx. 380kg
(Includes dust collector and air dryer)
Accessories Dust collector, Air dryer, Calibration jig, Core metal, etc.

We also accept inquiries about special orders, etc.

For details, please contact us from “Inquiries about new products”.

Tel. 042-572-1397 (Monday to Friday 9 a.m. to 5 p.m.)

Fax. 042-573-1520

Inquiring

Q & A

FAQs
What are the prices and commercial flow when it comes to purchasing products?

Please contact us from “Contact Us” on our website.

Can I do direct transactions?

Direct transactions are also possible; please contact us from the “Contact Us” section on the website for details.
☏ 042-572-1397 (Monday to Friday 9 a.m. to 5 p.m.)

What should I do if there is a device malfunction or trouble?

Please contact us from “Contact Us” on our website.
✉ service-desk@ueshima-seisakusho.com
☏ 042-577-1363 (Monday to Friday 9 a.m. to 5 p.m.)
6-5-22 Yaho, Kunitachi-shi, Tokyo, 186-0011

Regarding the warranty period?

We have set a guarantee period of 1 year from the inspection date. (Consumables are not included)
Details will be provided separately when the device is delivered.

I want a catalog, what should I do? 

Please download from “Click here to download the catalog” on each product page on our website.

Do you support overseas sales?

Yes, it is compatible. We have sales agents in the US, China, South Korea, Taiwan, India, Indonesia, Thailand, Vietnam, Malaysia, and Europe.    
For details, please contact us from the “Contact Us” website.

Is contract sample measurement possible for a fee?

This is possible depending on the device; please contact us from “Contact Us” for details.

Can I demonstrate the device?

This is possible depending on the device; please contact us from “Contact Us”.

Contact

We're here to help. For more information about our products and services, please fill out the form on the right.

042-572-1397 (Monday to Friday 9 a.m. to 5 p.m.)

Contact

For orders for repairs, calibrations, and services, please contact us using the contact details listed below.

service-desk@ueshima-seisakusho.com
042-577-1363 (Monday to Friday 9 a.m. to 5 p.m.)
6-5-22 Yaho, Kunitachi-shi, Tokyo, 186-0011
Thanks! Your submission has been received!
Oops! Something went long while appearing the form.